"Smart Logging" - Anytime, Anyplace

• In a wide range of temperatures: -20 to 60° ^1,2,3,4
• Reinforced insulation: Between input terminal and case⁵
3700 Vrms (one minute) or 600 Vrms/VDC (continuous)
• A wide variety of network functions: HTTP, FTP, DHCP, SNTP, E-mail, and others
• DC power supply (12 V-28 V) option available

• High speed measurement with a single unit (10 channels/10 ms or 60 channels/100 ms):
Shortest measurement interval of 10 ms
• Multi-interval: Enables mixing of three different measurement intervals in a single unit
(measurement intervals can be set for each module)
• Supports CompactFlash (CF) cards⁶ of up to 2 GB
Continuous data acquisition is possible on 60 channels at 100 ms for approximately ten days with a 2-GB card, or for three months on 60 channels at 1 s.
• MATH function on the main module available with the /M1 option.
• Collective data acquisition on 360 channels (via Modbus with the /M1 option)

1. The operating temperature range for the input modules and main module. The operating temperature range of the output modules is -20 to 50°.
2. Note that the power cord supplied with the main module differs depending on the operating temperature range (see the specifications on page 7). If the operating temperature range specification of the supplied standard power cord does not meet your requirements, we recommend that you select a screw-type terminal rather than the plug type for the main module power inlet, and supply your own power input cable.
3. The operating temperature range of the AC adapter used with DC power supplies is 0 to 40°.
4. Please consult with a representative for applications involving temperatures below -20°.
5. The withstand voltage value with the MX110 input module. For the withstand voltage values of other input and output modules, please refer to the specifications for those modules (GS 04M10B01-01E).
6. CF card not included (sold separately).

System Configuration

Standard Configuration

A custom MW100 measuring system is comprised of three elements; the MW100 main module, MX Series input/output modules, and MX150 Series base plate. The system can be bench mounted as-is or DIN rail mounted for rack or panel installations. A DIN rail-mounting bracket is included with the MX150.

The input/output modules, base plate, and accessories are all the same as those for the MX100 DAQMASTER series (AC adapter is for the MW100 only).

Input Modules

Level (24 V logic), Vth = 12 V

Output Modules

Base Plate

Base plates available for all configurations, from 1 to 6 input/output modules. When used for the MW100/MX100, you must replace the attachment with the one that comes standard with the MW100/MX100.

Accessories

Connector Covers Connector covers for open slots  AC Adapter (772075) AC adapter for the DC power model. Operating temperature range: 0 to 40° *Only for the MW100

Accessories (Removable Terminal)

	All input/output terminals are removable except for those of the MX112-NDI-M04. If multiple terminals are prepared ahead of time, no re-wiring is needed between measurements.

Advanced Data Logging

Measurement Information Shared

Measured Data Shared * Mail Server Required

Acquire up to 360 Channels in One System

A large data acquisition system of up to 360 channels can be assembled using multiple MW100s and standard MODBUS TCP Ethernet communications. When equipped with the /M1 math option, the MW100 can acquire up to 300 channels of external data from additional MW100 units or other devices such as a PLC using MODBUS TCP communications. This provides a total system capacity of 360 channels (60 built-in measure channels + 300 external).

Serial MODBUS RTU communications (RS- 232 or RS-422A/485) can be ordered as a separate option with the same capability.

Connect to Other Devices

An optional serial MODBUS RTU interface provides data exchange functions with other devices such as recorders, PLCs and controllers. In this mode, MW100 can serve as expansion I/O or as a data acquisition terminal for another connected device.

Remote Data Acquisition

Screen updating may be slower depending on the communication environment.

When the measurement location is located remotely from the data monitoring station, a dial up phone connection can be used for communications. All MW100 web browser-based data monitoring and FTP functions can be used via this connection for remote data acquisition applications.

Time Synchronization

The MW100 can synchronize its clock to a network time-server using SNTP (Simple Network Time Protocol), allowing any number of MW100s in a system to have precisely matched time. Both SNTP Server and Client modes are supported. In Server mode, one MW100 can acquire time data from a server using Client mode. It can then serve time data in Server mode to other MW100s that function as Clients. Clock synchronization functions are allowed only when the measurement interval within the unit is two seconds or longer.